| Product model: HYJ-50 The controller is specially designed for matching production of pattern machines. There are 101 kinds of Fixed seam samples from 0 to 100, and 101 to 140 40 kinds of programming stitches that can be programmed by the customer (up to 80 pins per seam); 150 to 250 101 kinds of joint suture samples. Each joint sample can be combined by any two fixed seam sample or a fixed seam sample plus a programming joint. It has automatic memory function for customers' seam, seam size, programming joint and combined seam, and will not be lost due to the power supply of the on / off controller. The controller panel has eight buttons, two indicator lights and a LCD screen. The operation methods are as follows: First, set the internal parameters of the controller. First press the "modify" key, then open the power supply of the controller, and then release the "modify" key; that is, enter the internal parameter setting interface; the coefficient of seam amplitude: the amplitude of the seam is constant; the greater the value, the greater the swing of the needle; this parameter is generally set by the manufacturer of the pattern maker. Motor speed: the greater the value, the greater the speed of the stepper motor; this parameter is generally set by the manufacturer of the pattern maker. Seam pattern display: it can be "point by point" (showing the location of each point of the seam sample) or "connecting line" (showing the location of each point of the seam sample). Buzzer: it can be "open" (every click of a button, or a turn of the spindle every turn, a buzzer is called) or "off" (buzzer does not call). Move the cursor position according to the key of the button and click the key to modify the content of the cursor position; press the "confirm" button to exit. Note: the coefficient of seam width and motor speed should not be 0. Two. Set seam and seam width. 1. Click the "modify" key to display the cursor on the number after the seam or slit. 2, press the "or" key to move the cursor around. 3, press the "button" or "key" to make the cursor position data add or subtract; 4, continue to press ",", "," or "key" to modify the data of other locations. 5. Press the "confirm" button to exit the set seam and the seam status, and the cursor will disappear. Three. Modify the combined seam sample. 1, click the combination button, the light on the combination key, and the cursor on the LCD screen. 2, press the "or" key to move the cursor around. 3, press the "button" or "key" to make the cursor position data add or subtract; 4, continue to press ",", "," or "key" to modify the data of other locations. 5, press the "confirm" key, quit the modification of the combined seam sample state, the lights on the combination key will disappear, and the cursor will disappear. Four. Programming 1, click the "programming" button, the key on the programming key is bright, and the cursor appears on the LCD screen. 2, press the "or" key to move the cursor around. 3, press the "button" or "key" to make the cursor position data add or subtract; 4, continue to press ",", "," or "key" to modify the data of other locations. 5. Press the "confirm" button to set the location of each needle. 6, press the "or" button to move the light marking line (cursor becomes a vertical line, indicating the number of pins), the number of pins of the display (that is: programming on the first few pins) plus or minus; 7, press the "button" or "key" to make the middle position of the light marking line move up and down. The position of the monitor is added or reduced. 8, continue to press the ",", "or" button to modify the position of the other needles until the position of the needles shown on the display is similar to the required stitches. 9, press the "confirm" button to exit the programming state, the lights on the programming keys disappear, and the cursor vanishes. Five, installation: 1, three core power line to AC 220V 2, four core white air plugging 57 stepper motor, stepper motor current 2.5A per phase. If the steering of the motor is not correct, the two white lines in the control box will be switched to the motor driver. 3, 9 core flat to the control panel. 4, control panel Holzer sensor board installation: Holzer sensor used to detect the spindle speed, spindle on two magnetic steel, a magnetic steel N pole outward, a magnetic steel S pole outward, two magnetic steel location 180 degrees; Holzer sensor alignment magnet steel, spindle rotation each turn Holzer sensor receives magnetic steel S pole signal and a N pole signal. 5, photoelectric sensor: used to detect the vertical position of the needle. The stepper motor drives the light plate and the needle to swing around, and the light plate should be wider. When the stepping motor is swinging to one side, the light plate is always light. When the other side is swinging, the light plate is always not light. The position of the light gauge plate is adjusted, so that the light plate is just not perpendicular to the vertical (middle) position of the needle. Note: 1: when the controller is powered up, it will automatically find the vertical position of the needle; if the stepper motor keeps moving, it indicates that the stepper motor's steering is not correct or the photoelectric sensor is bad. If the stepper motor's steering is not correct, the two white lines of the stepping motor driver in the control box can be switched. 2: stepper motor, but not pendulum. A: Holzer sensor plate is bad. B: Holzer sensor plate is too far away from magnetic steel. C: the two magnetic steel is not a N pole outward, a S pole outward. D: the slot coefficient of the control panel is set to 0. E: the motor speed of the control panel is set to 0. F: the driver of the stepper motor in the control box is bad. G: stepper motor is bad. H: bad connection or mechanical failure. 3: the actual swing amplitude of the needle is not the set width; A: the setting value of the slot coefficient of the control panel is not correct. B: the minute fraction of the stepper motor driver in the control box is not correct. The three switches of 1, 2 and 3 of the driver should be switched to 16 segments. C: the setting current of the stepper motor driver in the control box is too small; the three, 5, 6, 7 switches of the driver should be switched on, so that the current can be set to 2. 5A. D: the motor speed setting value of control panel is too small. |
|
|
|
|
|
|
|
| |
|
| |
